One of the biggest realities of wearing hair systems long-term is color oxidation. Over time, exposure to sunlight, daily washing, and regular wear cause human hair systems to fade. While the unit might still have plenty of structural life left, faded hair makes it look tired, mismatched, and noticeably lighter than your natural bio hair.
I’ve been testing and documenting various non-surgical hair units on my channel, and today we’re tackling a crucial maintenance step: how to safely dye and refresh a faded Lordhair thin skin (Poly Base) system without ruining the transparent base.
The Experiment: Learning from Past Mistakes
Before dyeing my current daily unit, I ran a trial run on an older Lordhair 0.03mm (Lite UTS / Ultra Thin Skin) system with 80% denisty. That older unit had oxidized significantly and turned quite light and brassy.
While the test proved that the color took phenomenally well, it also revealed a critical trap: dye penetration into the poly base.
On that test unit, I didn’t protect the frontal hairline. The dark dye soaked directly into the ultra-thin polyurethane membrane, leaving a dark, tinted edge that looked almost like window tint. I even attempted to salvage it by applying bleach to the front poly edge to lift the pigment. Bleach only damaged the hair, caused severe frontal shedding, and shifted the base to an unnatural golden-brown stain, never returning it to clear.
The Key Takeaway: The hairline transition is everything. While minor base staining at the crown doesn't matter because it rests flush against your scalp, any tint along the exposed front edge will completely destroy the natural look of a transparent hairline.
Understanding the Hair: Real Hair vs. Synthetic Gray
*Lordhair grey hair systems come in two kinds: Synthetic fibre and human hair. For a grey percentage of 60% or higher, units can often come recommend with the human grey hair option. So anyone trying this method should first check whether their grey is synthetic or human hair.
The unit featured in this restoration is a Lordhair 0.06mm SuperSkin system (100% hair density) with approximately 40% to 50% gray hair.
If you have a mixed-gray hair system, that incorperates synthetic gray hair, here is how dyeing works:
Human Hair Fibers: The natural brown/black human hair absorbs the dye formulation completely, restoring rich, deep contrast.
Synthetic Gray Fibers: The gray hairs in these systems are synthetic fibers that do not absorb standard hair dye.
Because the synthetic grays resist the dye, the hair system maintains its original salt-and-pepper ratio. You restore the dark base tone without accidentally wiping out your natural age-appropriate gray highlights.
Tools & Supplies Used:
Lordhair Thin Skin System (0.06mm SuperSkin or 0.03mm Ultra-Thin Skin)
Black Hair Dye / Shampoo Formulation (e.g., Rilsik Black Hair Shampoo)
Petroleum Jelly (Vaseline) – Essential protective barrier
Protective Gloves (to prevent deep skin hand staining)
Hairband / Elastic Clip (for sectioning)
Mild Cleanser (e.g., Shaklee Basic-H or an ultra-gentle, residue-free soap)
Moisturizing Hair Conditioner / Leave-In Hair Oil
Sink / Basin with Lukewarm Running Water
Step-by-Step Application Guide
Apply a generous layer of petroleum jelly (Vaseline) directly along the front hairline border. Coat both the edge and slightly underneath the front underside of the polyurethane membrane. This creates a hydrophobic shield that prevents liquid dye from creeping under the base and permanently staining the front perimeter.
Tie or pin back the bulk of the hair using an elastic band. You want distinct control over the delicate front transition before treating the body of the system.
Put on your gloves. Dispense the dye product and work it until it reaches a uniform, creamy consistency.
Front First: Carefully apply the product slightly behind the front hairline, specifically avoiding the exposed poly edge and middle parting zone.
Mid-Lengths & Crown: Release the hairband and work the solution thoroughly through the crown and rear lengths.
Pro-Tip: Do not wear good clothing during this process, and rinse any stray drips in your sink immediately.
Allow the dye formulation to sit on the hair for 10 to 15 minutes. Keep an eye on timing to avoid over-saturating the unit.
Hold the system securely by the protected front hairline edge. Rinse the hair backward under lukewarm running water, flowing the dark runoff away from the front hairline. Keep rinsing until the runoff water transitions from dark to mostly clear.
Use a gentle, residue-free cleanser (like Shaklee Basic-H) to thoroughly wash out the petroleum jelly from the front poly perimeter. Residual Vaseline will prevent adhesive or hair system tapes from bonding securely during your next installation.
Follow with a rich conditioner. Chemical dyes naturally pull moisture from human hair systems. Rinse the conditioner out mostly, but leave a minute trace behind (or follow with a light leave-in hair oil) to restore natural softness and manageability.
Results and Longevity
Inspecting the system post-drying reveals an immediate difference:
The Color: Deep, vibrant, and evenly restored without altering the synthetic gray balance.
The Base: The front poly membrane remains crystal clear and transparent, blending invisibly into the skin once mounted.
Unit Lifespan: Manufacturers generally rate 0.06mm skin systems for approximately 2+ months of everyday wear. By refreshing the faded color at the 7–8 week mark, you can easily push the usable lifespan of the unit to 3 full months or beyond.
A tiny amount of shedding around the crown or front over weeks of combing and reinstalling is completely normal. Trimming back a millimeter of the front hairline every few reinstallations keeps the perimeter looking sharp and dense. Combined with an occasional color refresh, your hair system stays natural, healthy, and undetectable.
If you are planning to pick up a system, head over to Lordhair.com. Check out their virtual try-on feature (where you can upload a photo to preview different base styles and cuts), and make sure to use code MIKE20 at checkout to save on your order.